stock clutch is slipping - pos

[hsspunk]

remember i had a thread on sf about my car boosting to 19psi on stock compression? i found the problem. the clutch is slipping. right after a strong pull, the car revvs very high very quick from a stop and doesn't really go anywhere. so the stock clutch is good for about 1 pull, then when it heats up, it's a POS and doesn't hold any power. so this is what is causing my boost spike

too bad i can't afford to buy a new clutch for a while.......

holy shit this smily is fuckin great. had to test it out haha :op:

[SupaSupraSE]

lmao. Same thing here, boosted through third and the clutch slipped for the first time.. Its like aids, it only gets worse from here...

:roflwtf:

[Kirk]

I boosted hard for 2 months before my stock clutch started slipping... it only slipped on top end (past 5K)...took it out and it still had some meat on it

[scnat]

I boosted hard for 2 months before my stock clutch started slipping... it only slipped on top end (past 5K)...took it out and it still had some meat on it


10 psi:bowdown: :bowdown: :bowdown:

[Kirk]

10 psi:bowdown: :bowdown: :bowdown:

stock clutch :gfight:

[soarerflame]

The BamburiMS clutch,6 puck carbonkevlar with heavy duty pressure plate, holds great at 22psi on a buddies RB25 S13. Hey its only 275 bucks shipped give em a call at 615 579 6482

good luck with it

[SupaSupraSE]

More info on the clutch...? It will work on a w58 MKIV 5 speed? How does it compare to other brand new clutches? (RPS, etc)

Please PM me with details and be as not bias as possible.

Thx

[Bean]

The BamburiMS clutch,6 puck carbonkevlar with heavy duty pressure plate, holds great at 22psi on a buddies RB25 S13. Hey its only 275 bucks shipped give em a call at 615 579 6482

good luck with it

I doubt they make it for the W58.
I heard most of the Nissan-based clutch companies dont make clutches for Toyota motors because of the torque difference :)

Best bet is to go with what works and what's available

[Jr24dawg]

my stock clutch would slip bad in third when i was still na. i got the hpf 6 puck with rps pressure plate a week before the turbo kit showed up... a little over kill i think. im pretty sure my tranny will fail way before my clutch will

[kevganzon]

my stock clutch would slip bad in third when i was still na. i got the hpf 6 puck with rps pressure plate a week before the turbo kit showed up... a little over kill i think. im pretty sure my tranny will fail way before my clutch will

how do you like the HPF clutch???

[Daston]

I only had my new clutch fitted 1k miles ago do you think I will need to change it?

[Bromy]

When you finally go turbo and upping the boost yes, mine slips in 4th and 5th with 12psi and clutch is only 8k old, rps 6 puck next

[Daston]

I was only going to boost to 5.8psi as I will be running stock injectors and HG as I cant go for the stage 2 kit due to insuance.

[Bromy]

I was only going to boost to 5.8psi as I will be running stock injectors and HG as I cant go for the stage 2 kit due to insuance.

You will be fine with standard clutch then bud, you will deffo want to up the boost though once you get the bug :naughty:

[Daston]

Yeah thats what I am afraid of well its only a couple of years till I am 25 so it should go down a bit by then.

[soarerflame]

The BamburiMS clutch,6 puck carbonkevlar with heavy duty pressure plate, holds great at 22psi on a buddies RB25 S13. Hey its only 275 bucks shipped give em a call at 615 579 6482

good luck with it


Its basically a heavy duty pressure plate with a 6 puck copper ceramic and sprung hub. It lived forever in my sc till my tranny busted. BMS sells them for the SC for 400 shipped.

[scottie G]

The BamburiMS clutch,6 puck carbonkevlar with heavy duty pressure plate, holds great at 22psi on a buddies RB25 S13. Hey its only 275 bucks shipped give em a call at 615 579 6482

good luck with it
Good lookin out thanks