Raven
09-26-2005, 08:50 PM
Here are the specs on my car. If I missed anything I will post it later.
The car is a beast and is crazy fast. Lance (Toyomoto) worked on the car after I bought it from Ethan. He basically rebuilt the moter. After 6 months went by I needed more. So it was sent to RTC. George did all the head work. And also put my rods in. The best is he tuned the car..... WOW the guy is the best at tuning Motec's. He can build a car.
HEAD
Port polished (machined by Dave Localio at HeadGames)
Ti Valves
Ti dual springs
Ti Retainers
HKS Cams (272) Intake & Exhaust
unorthodox Cam Timing Gear Intake & Exhaust
aftermarket Damper
Engine Modifications
80mm TB
GTE Bottom end
Carillo Rods
SPS Carr Rod Bolts
Fuel System
PHR 17.5mm ID Fuel Rail
HKS 720cc Injectors
Dual TT fuel pumps
Kevlar fuel lines
Aeromotive Fuel Pressure Regulator
100 psi liquid filled FP gauge
Turbo System
Power Master .70mm Turbo
3" downpipe & midpipe
2.5" IC piping
Blitz Blow Off Valve
Spearco 24" Intercooler
Electronics
Motec M4 PRO ECU
Motec Wide Band Lambda Option, Sensor
Raychem Custom Wiring Harness
NTC Air Temp Sensor
3 BAR MAP Sensor
TRD Triple 60mm Gauge Pod
Apexi Boost, Oil Press, Fuel Press 60mm
Blitz Boost Controller
Driveline
6 speed getrag
RPS Stage 3 Clutch
Toyomoto custom drive shaft
TRD Limited Slip Differential
Rev limiter is set at 8500
In my garage is Lance's tubular header plus a PT71 GTS .81 AR
Just itching to put them in :)
The car is a beast and is crazy fast. Lance (Toyomoto) worked on the car after I bought it from Ethan. He basically rebuilt the moter. After 6 months went by I needed more. So it was sent to RTC. George did all the head work. And also put my rods in. The best is he tuned the car..... WOW the guy is the best at tuning Motec's. He can build a car.
HEAD
Port polished (machined by Dave Localio at HeadGames)
Ti Valves
Ti dual springs
Ti Retainers
HKS Cams (272) Intake & Exhaust
unorthodox Cam Timing Gear Intake & Exhaust
aftermarket Damper
Engine Modifications
80mm TB
GTE Bottom end
Carillo Rods
SPS Carr Rod Bolts
Fuel System
PHR 17.5mm ID Fuel Rail
HKS 720cc Injectors
Dual TT fuel pumps
Kevlar fuel lines
Aeromotive Fuel Pressure Regulator
100 psi liquid filled FP gauge
Turbo System
Power Master .70mm Turbo
3" downpipe & midpipe
2.5" IC piping
Blitz Blow Off Valve
Spearco 24" Intercooler
Electronics
Motec M4 PRO ECU
Motec Wide Band Lambda Option, Sensor
Raychem Custom Wiring Harness
NTC Air Temp Sensor
3 BAR MAP Sensor
TRD Triple 60mm Gauge Pod
Apexi Boost, Oil Press, Fuel Press 60mm
Blitz Boost Controller
Driveline
6 speed getrag
RPS Stage 3 Clutch
Toyomoto custom drive shaft
TRD Limited Slip Differential
Rev limiter is set at 8500
In my garage is Lance's tubular header plus a PT71 GTS .81 AR
Just itching to put them in :)